Hose Crimping Machine Selection Guide
Choosing a crimper comes down to four questions: how large is the hose, how much closing force the ferrule needs, how many assemblies per hour you build, and where the machine will stand. Work through the four steps below, then confirm the details with our engineers before ordering.
Φ6–25 mm for small assemblies, Φ6–51 mm for the bulk of hydraulic work, Φ4–150 mm for large bore, up to Φ530 mm for industrial bundles.
300–600 T covers most Φ6–51 mm work. Large bore and high-pressure ferrules need 800 T to 2500 T, with 4500 kN units for extreme sizes.
Manual and portable units run around 10 pcs/h; standard electric machines 120–400 pcs/h; high-speed and CNC models reach 800 pcs/h.
Bench, vertical floor-standing, portable, CNC or heavy-duty press — determined by assembly length, floor space and whether the machine travels to site.
Step 1–2: match the hose range to a model
Recommended shortlists by hose inside diameter. Full datasheets for every model are on the BRT hose crimping & locking range page.
| Hose ID range | Working range in catalogue | Recommended models | Closing force / output | Typical application |
|---|---|---|---|---|
| Φ6–25 mm Small-bore assemblies, pilot lines |
Φ6-25mm | BRT-CM25 | CM25: 100T / 70 pcs/h | Automotive hose, small-batch repair |
| Φ6–38 mm Compact workshop crimping |
Φ6-38mm | BRT-CM38 · BRT-CM38P | CM38: 400T / 200 pcs/h CM38P: 300T / 200 pcs/h |
General hydraulic up to 38 mm, mobile service |
| Φ6–51 mm — standard The workhorse range |
Φ6-51mm | BRT-CM51 · BRT-CM51WS · BRT-CM51P | CM51: 500T / 120-400 pcs/h CM51WS: 300T / 200 pcs/h CM51P: 400T / 120 pcs/h |
Industrial hose assemblies, repair shops |
| Φ6–51 mm — high output Volume production |
Φ5-51mm / Φ6-51mm | BRT-CM51SM · BRT-CM51A | CM51SM: 600T / 800 pcs/h CM51A: 2200KN / 300 pcs/h |
Assembly lines, 300-800 pcs/h |
| Φ6–76 mm Medium bore |
Φ6-76mm | BRT-MT76 · BRT-CM76H | MT76: 800T / 200 pcs/h CM76H: 2800KN / 300 pcs/h |
Construction & agricultural equipment |
| Φ4–102 mm Large bore |
Φ4-102mm / Φ6-102mm | BRT-CM102 · BRT-MT102 | CM102: 750T / 200 pcs/h MT102: 1500T / 200 pcs/h |
Heavy machinery, large return lines |
| Φ4–150 mm Extra-large bore |
Φ4-150mm / Φ6-150mm | BRT-MT150 · BRT-CM150 | MT150: 2500T / 200 pcs/h CM150: 650T / 200 pcs/h |
Mining, oil & gas, shipyard |
| Φ90–530 mm Ultra-large / industrial |
Φ200-315mm / Φ6-530mm / Φ90-200mm | BRT-CM200U · BRT-CM315U · BRT-CM530H | CM200U: 500T / — CM315U: 1000T / — CM530H: 4500KN / 300 pcs/h |
Steel Mill, dredging, industrial hose bundles |
Step 3–4: form factor and production volume
Once the range is fixed, the machine body decides how the workshop works — a bench unit, a floor-standing press, a van-mounted portable, or a CNC cell.
| Form factor | Models | Working range | Closing force | Output | Where it fits |
|---|---|---|---|---|---|
| Horizontal / bench | BRT-CM51 · BRT-CM51WS · BRT-CM51QY | Φ6-51mm | 300T / 500T / 600T | 120-400 pcs/h / 200 pcs/h | Fixed workshop station, most common layout |
| Vertical, floor-standing | BRT-CM51V-2 · BRT-CM51V-3 · BRT-CM51V-4 · BRT-CM51L | Φ1-90mm / Φ4-51mm / Φ6-51mm | 500T / 600T | 120-400 pcs/h / 200 pcs/h | Long or flanged assemblies, saves floor space |
| Portable / mobile service | BRT-CM51CZ · BRT-CM38P · BRT-CM25E-M | Φ10-27mm / Φ6-38mm / Φ6-51mm | 300T / 490T / — | 10 pcs/h / 200 pcs/h | On-site repair, van-mounted service |
| CNC / digital control | BRT-CM51N · BRT-CM51N-2 · BRT-CS51N | Φ6-40mm / Φ6-51mm | 520T / 540T | High-speed automatic cycling / — | Repeatable settings, high repeat volume |
| Heavy-duty press | BRT-CM76H · BRT-CM102H · BRT-CM330H | Φ4-102mm / Φ50-330mm / Φ6-76mm | 1800T / 2800KN / 4500KN | 200 pcs/h / 300 pcs/h | Large bore, high tonnage, continuous duty |
| Ultra-thin / ultra-large | BRT-CM200U · BRT-CM315U | Φ200-315mm / Φ90-200mm | 1000T / 500T | — | Oversized fittings, tight access, bundle work |
Complete the line: cutting, skiving, testing
A crimper on its own leaves two failure points open — a ragged cut and a scored liner. Pair the press with the matching process equipment.
| Process step | Recommended models | Working range | Why it matters |
|---|---|---|---|
| Hose cutting | BRT-CU38 · BRT-CU51QD · BRT-CU51N | Φ6-51mm | Square, dust-free cuts before crimping |
| Hose skiving | BRT-ST51-1 · BRT-ST51-2 · BRT-ST64 · BRT-ST150N | Φ51-150mm / Φ6-51mm / Φ6-64mm | Strip cover without scoring the liner |
| Shrink crimping | BRT-SM57 · BRT-SM57-2 | 48-57mm | 48-57 mm ferrule / sleeve locking |
| Swaging & installation | BRT-ZL75 · BRT-ZL260 | 50-150mm / Φ50-150mm composite hoses | Composite and large-bore assembly |
| Nut crimping | BRT-NC80 | Φ6-51mm hose end fittings | Hose end fitting nuts, Φ6-51 mm |
| Pressure testing | BRT-SY40 · BRT-SY400 · BRT-SY450B | 0-400MPa / 350-450MPa / Φ6-51mm hose assemblies | Proof and burst verification |
Matching hydraulic hose fittings
Every machine above is delivered to crimp the BRITOP fitting programme — eight series, metric through JIS dual seal.
| Series | Scope |
|---|---|
| Metric | DIN/ISO metric crimp fittings, 12 codes |
| BSPT | Tapered BSPT fittings, 12 codes |
| JIC | SAE JIC 37° flare, 12 codes |
| SAE Flange | 9 codes |
| SAE Flange & Cone | 18 codes |
| BSP | 23 codes |
| Other Connectors | 24 codes, adapters on request |
| JIS Dual Seal | 12 codes |
Frequently asked questions
1. Which BRT model suits a Φ6–51 mm hose?
The Φ6–51 mm range is covered by more than a dozen models. BRT-CM51 (500 T, 10 die sets) is the general-purpose choice; BRT-CM51P (400 T, 1.6 kW) suits lower power supply; BRT-CM51WS (300 T) and BRT-CM51BY (300 T) are the compact workhorses; BRT-CM51SM / BRT-CM51CSD reach 800 pcs/h for volume work.
2. How much closing force do I need?
Match the ferrule outside diameter and the hose working pressure against the working range and force columns. Every model above lists both. If your assembly is close to the edge of a range, send us the hose spec and fitting code and we will confirm the model in writing before you order.
3. Are dies included?
Yes. The “Die Sets” column shows the standard quantity shipped with each machine — 10 sets on BRT-CM51, 12 on BRT-CM51WSSK, 20 on BRT-MT150. Non-standard sizes and custom profiles are made to order.
4. What voltage are the machines built for?
Motor power is listed per model (for example 3 kW / 4 kW or 5.5 kW). Machines are configured for 220 V to 380 V according to destination; state your voltage and phase when ordering.
5. Can the same machine crimp composite or corrugated hose?
Not always. BRT-CM68V handles Φ6–51 mm corrugated hose, and the BRT-ZL series (75 T / 260 T) is built for 50–150 mm composite assemblies. Tell us the hose construction before selecting a crimper.
6. Where is the full specification table?
The complete 89-row table — every BRT model with die sets, motor power, output, dimensions and weight — sits on the hose crimping & locking range page.
All working ranges, closing forces and outputs quoted on this page come from the published BRT catalogue dated 2026. Values marked “—” are not listed in the datasheet and are confirmed per order.